Report Outlines Perovskite Technology Roadmap For India

P3C, in association with ISMA, recommends prioritizing single-junction perovskite solar cells before moving to silicon-perovskite tandem technology
A new report highlights the technical and economic advantages of single-junction perovskite solar technology for India.
A new report highlights the technical and economic advantages of single-junction perovskite solar technology for India. (Image Credit: P3C Technology and Solutions)
Published on: 
Key Takeaways
  • The report highlights the advantages of perovskites, including a tunable bandgap, lower temperature losses, and better low-light performance

  • Single-junction perovskite technology could reduce India’s import dependence and lower electricity generation costs by 30% to 40%

  • The report proposes a provisional ALMM category for perovskites with defined stability and reliability requirements

India has significantly expanded its solar cell and module manufacturing capacity over the past few years. However, the country still relies on imports for key raw materials, manufacturing equipment, and technology. A report by P3C Technology and Solutions, in association with the Indian Solar Manufacturers Association (ISMA), looks at how India can develop its own solar technology by investing in perovskites.

The report, titled Perovskite Solar: India’s Atmanirbharta Opportunity in Next Generation PV, discusses the technical and economic benefits of perovskites and the challenges in commercializing the technology.

Perovskite solar cells use a thin layer of semiconductor material with a specific crystal structure to absorb sunlight instead of a silicon wafer. One advantage of perovskites is a tunable bandgap. By changing the chemical composition of the absorber material, it is possible to adjust the range of sunlight it absorbs. This allows a perovskite cell to be placed on top of a silicon cell to capture a wider portion of the solar spectrum. Certified silicon-perovskite tandem solar cells have already crossed 35% efficiency at the laboratory level (see LONGi Sets 35.5% Silicon-Perovskite Tandem Cell Efficiency Record).

It also compares perovskites with advanced crystalline silicon cell technologies, including tunnel oxide passivated contact (TOPCon), heterojunction (HJT), and interdigitated back contact (IBC). TOPCon has lower manufacturing costs and is compatible with existing passivated emitter and rear cell (PERC) production lines. HJT requires fewer processing steps but uses more expensive materials and equipment, while IBC involves complex contact patterning on the rear side of the cell.

Rather than moving directly to tandem cells, the authors suggest Indian manufacturers start with single-junction perovskites. Manufacturers can first gain experience in absorber materials, encapsulation and reliability before integrating perovskite with silicon. India’s growing TOPCon cell manufacturing capacity could then serve as the base for tandem production.

Single-junction perovskite cells do not require polysilicon, ingots or wafers – the segments of the solar PV value chain where India’s import dependence is particularly high. Perovskites can also be manufactured using low-temperature, solution-based processes. According to the report, setting up a perovskite production line could require 70% to 80% less capital investment than a conventional crystalline silicon manufacturing line.

Another aspect the report looks at is the performance of perovskites under Indian climatic conditions. It cites a temperature coefficient of -0.1%/°C for perovskites, against around -0.3%/°C for TOPCon. Perovskites are also reported to perform better under low-light conditions.

For their calculations, the authors assume a capacity utilization factor (CUF) of 20% for crystalline silicon and 25% for perovskites. Based on these figures, the annual electricity generation per MW of installed capacity is around 1.75 million kWh for crystalline silicon and 2.19 million kWh for perovskites.

The estimated capital cost of a perovskite-based solar power plant is INR 22 to INR 28/W, against INR 38 to INR 42/W for crystalline silicon. With lower investment and higher annual generation, the report puts the levelized cost of electricity (LCOE) for perovskites at INR 1.5 to INR 1.9/kWh, compared to INR 2.4 to INR 2.7/kWh for silicon.

One area that needs more data, however, is degradation. Based on the current understanding of the technology at the pilot stage, the report assumes a degradation rate of 0.5% to 1% for perovskites. Protecting the cells from heat and moisture over a 25-year period and addressing concerns over lead content are among the challenges yet to be resolved.

Work on single-junction perovskites is already underway in India. P3C, a spin-off from the Indian Institute of Technology (IIT) BHU, operates a 100 kW pilot manufacturing line in Gurugram and aims to scale up to 1 GW by 2030. Its 30 cm² perovskite modules with an efficiency of around 15% are undergoing reliability testing at the National Institute of Solar Energy (NISE).

P3C has signed a memorandum of understanding (MoU) with NISE to set up shared testing facilities and develop standards for perovskite modules. Earlier this year, the company also launched a validation platform to help manufacturers assess module performance under outdoor conditions (see P3C Launches Perovskite Validation Platform In India).

Given the limited long-term field data, it is recommended to introduce a provisional category for perovskite modules under the Approved List of Models and Manufacturers (ALMM). Single-junction perovskite modules could be listed first, followed by tandem modules at a later stage. To qualify for full listing under ALMM, manufacturers would need to pass damp heat and thermal cycling tests and submit field performance data (see India Brings ALMM List-II For Solar Cells Into Force).